Drilling into brick, concrete, or block is one of the most punishing tasks for any drill bit. Standard wood or metal bits dull instantly or snap under the hammering action, turning a simple anchor install into a frustrating, dusty mess. The right bit makes the difference between a clean hole in seconds and a broken bit in minutes.
I’m Mohammad Maruf — the founder and writer behind WellFizz. I’ve spent countless hours analyzing carbide grades, shank geometries, and flute designs to find the bits that actually survive repeated contact with masonry without self-destructing.
This guide breaks down the five best options based on real-world durability, material compatibility, and shank type, so you can confidently pick the best drill bits for brick for your next project.
How To Choose The Best Drill Bits For Brick
Masonry drilling is tough on tooling. The key to a smooth experience is matching the bit’s shank type, tip material, and cutting geometry to your drill and the material you’re penetrating. Getting these wrong leads to slipping, overheating, and breakage.
Shank Type: Hex vs. SDS Plus vs. Straight
A hex shank locks into standard hammer drill chucks without slipping under high torque — ideal for light to medium masonry work with ⅜-inch or smaller bits. An SDS Plus shank uses a grooved, spring-loaded system for rotary hammer drills, allowing deeper penetration and faster dust removal in thicker concrete or reinforced block. Straight shanks are common on basic bits but are more prone to spin-out in the chuck.
Carbide Tip Grade and Geometry
Look for YG8X or equivalent tungsten carbide brazed onto the cutting head. Asymmetric or cross-ground tips self-center better, reducing wander on smooth brick faces. A 135-degree split point is standard for masonry — it bites into the surface rather than skating across it.
Flute Design for Dust Evacuation
Deep, wide U-flutes with a steep spiral angle help pull pulverized dust out of the hole. Shallow or straight flutes clog quickly, causing the bit to overheat and lose hardness. For holes deeper than 3 inches, a well-designed flute is critical to completion.
Quick Comparison
On smaller screens, swipe sideways to see the full table.
| Model | Category | Best For | Key Spec | Amazon |
|---|---|---|---|---|
| Bosch LBHXS7U | Premium | General masonry, impact driver use | 1/8″ to 3/8″ bits | Amazon |
| WildBossy Concrete Carbide Set | Premium | Multi-material, home projects | 5/32″ to 1/2″ range | Amazon |
| Sabre Tools 5/8″ SDS Bit | Premium | Deep holes, thick concrete | 39-inch length | Amazon |
| Wensilon Extra Long Bit | Mid-Range | Extra-long reach, block walls | 12-inch total length | Amazon |
| toolant 3/16″ Set | Mid-Range | Budget-friendly, small holes | 10-piece 3/16″ bits | Amazon |
In‑Depth Reviews
1. Bosch LBHXS7U 7-Piece Hex Shank Set
The Bosch LBHXS7U set gives you seven sizes from 1/8-inch up to 3/8-inch, each with an asymmetric diamond-ground carbide tip. That asymmetrical geometry helps the bit stay centered on hard brick faces, reducing the walk that often happens with symmetrical tips.
The upgraded hex shank lets you use these bits in both impact drivers and hammer drills, which adds versatility if you switch tools frequently. The milled U-flutes are deep-cut and spiral aggressively, ejecting dust fast enough that you won’t need to back the bit out constantly to clear the hole.
Bosch makes its own carbide in-house, and the tip bonding holds up under heavy hammering. Customers report drilling through stucco, CBS block, and even thin steel without dulling the edge. The main size index on the plastic case is printed small, so keep the bits organized by size in the case to avoid guesswork.
Why it’s great
- Asymmetric carbide tip reduces bit wander on starting
- Hex shank fits impact drivers and regular chucks
- Deep spiral flutes clear dust efficiently
Good to know
- Size markings on case are hard to read
- Set maxes out at 3/8-inch — no larger bits included
2. WildBossy Concrete Carbide Drill Bit Set (10-Piece)
This WildBossy set spans ten sizes from 5/32-inch to 1/2-inch, a practical range for installing wall anchors, shelf brackets, and bathroom hardware. The tips are made from tungsten steel carbide with a 135-degree split point, which helps the bit cut aggressively instead of skating across glazed tile or dense brick.
The hex shank provides a positive lock in the drill chuck, reducing the slipping that can mar the shank over time. For glass and ceramic tile, the instructions advise using low speed and water cooling — a nice touch that shows the set was designed with real-world multi-material use in mind, not just concrete.
Customer feedback notes the bits arrive sharp and stay sharp through multiple concrete and masonry holes. One reviewer successfully drilled concrete and tile without issue. The only common complaint is that some bits run slightly smaller than the stated diameter, which could matter for tight anchor fits.
Why it’s great
- Wide size range covers most home use cases
- Split-point tip reduces start-up wander
- Hex shank locks securely without slipping
Good to know
- Some bits run slightly understated diameter
- Not designed for rotary hammer drills
3. Sabre Tools 5/8″ x 39″ SDS Plus Rotary Hammer Drill Bit
If you need to drill all the way through a thick foundation wall or pass cable through a cinder block structure, this Sabre Tools SDS Plus bit is the specialist pick. With a 39-inch overall length and a 5/8-inch diameter, it reaches depths that standard bits cannot touch.
The self-centering two-flute carbide tip is designed to keep cutting speed high while the titanium nitride coating reduces friction heat. The SDS Plus shank fits every major rotary hammer brand — Bosch, DeWalt, Hilti, Makita, Milwaukee — and the spring-loaded retention prevents the bit from pulling out under heavy feed pressure.
Real users have driven this bit through 18-inch-thick cinder block in about five minutes using a rotary hammer, and others have used it to drill through rock for grounding rod installation. The bit flexed on embedded rocks but held up with adjusted pressure. It is heavy at 26 ounces, so a rotary hammer with a side handle is strongly recommended.
Why it’s great
- 39-inch length reaches deep wall cavities
- SDS Plus shank fits all major rotary hammers
- Carbide tip survived rock and embedded stone
Good to know
- Heavy bit requires a rotary hammer with side handle
- Only one size — not suitable for small pilot holes
4. Wensilon Concrete Drill Bit (3/4″ x 12″)
The Wensilon bit is a single 3/4-inch by 12-inch cross-type double-threaded bit built for deep reaches in block and concrete. The cross cutter head design bites more aggressively than a standard single-point tip, making it effective for wall pass-throughs and spigot hole widening.
Made from high-strength alloy steel, the double-threaded flute geometry helps shed stone powder efficiently, reducing the binding that often happens with long bits. It fits most standard impact drills via a straight shank, though users with rotary hammers will get better speed and less wrist strain.
Customers report drilling 12 to 15 holes in concrete block without killing the edge, and one user widened a stone wall hole for a spigot with good results. A common note is that the bit bites hard just before breakthrough — several reviewers recommend easing pressure near the end to avoid wrist torque that can cause injury.
Why it’s great
- Cross-type double thread clears dust quickly
- 12-inch length reaches deep block cavities
- Aggressive carbide tip starts holes fast
Good to know
- Straight shank can slip in standard chucks
- Bites hard at breakthrough — use steady pressure
5. toolant 3/16″ Concrete Drill Bit Set (10-Piece)
Toolant delivers ten identical 3/16-inch bits with YG8X tungsten carbide tips and a shockproof hex shank design. At this price point you get a high quantity of bits that perform well enough for small anchor holes in brick, block, and even glass or tile when used at low speed.
The hex shank provides excellent stability in hammer mode, which is a real advantage over budget straight-shank bits that twist under load. Each bit has sharpened side edges that maximize carbide surface contact, helping the cutting edge engage the masonry for faster drilling rather than just hammering the surface.
Customer feedback consistently praises the value — each bit yields a handful of holes before dulling, and at this price per bit it makes practical sense to treat them as consumable items. One reviewer drilled concrete, cinder block, and rock without the bits chipping or dulling prematurely. They are not designed for deep or large-diameter holes, but for light duty they are hard to beat.
Why it’s great
- Ten bits give plenty of backup spares
- Hex shank prevents chuck slip in hammer mode
- YG8X carbide tip offers solid durability for the price
Good to know
- Only one size — not useful for larger holes
- Bits are consumable-grade, not heavy-duty
FAQ
Can I use masonry bits in a regular drill without hammer mode?
How do I prevent the bit from walking on glazed brick?
What is the practical difference between a hex shank and an SDS Plus shank?
Final Thoughts: The Verdict
For most users, the best drill bits for brick winner is the Bosch LBHXS7U 7-Piece Set because it combines asymmetric carbide tips, a versatile hex shank, and deep flute geometry in a ready-to-go case. If you want a broad size range for home projects, grab the WildBossy 10-Piece Set. And for deep concrete penetrations that require a rotary hammer, nothing beats the Sabre Tools 39-Inch SDS Plus Bit.
Mo Maruf
I created WellFizz to bridge the gap between vague wellness advice and actionable solutions. My mission is simple: to decode the research and give you practical tools you can actually use.
Beyond the data, I am a passionate traveler. I believe that stepping away from the screen to explore new environments is essential for mental clarity and physical vitality.