Our readers keep the lights on and my morning glass full of iced black tea. As an Amazon Associate, I earn from qualifying purchases.7 Best Corn Feeder For Deer | 250 Lbs Of Gravity Fed Corn

Check Price on Amazon

The Pro Hunter III is the first mainstream corn feeder for deer that lets you adjust ten daily feed events from your phone without walking within three hundred feet of your stand. The Bluetooth connection bridges through an Edge 3 cellular camera if you need remote access from miles away, and the spin plate offers three RPM settings — high, medium, or low — so you can dial in the exact spread radius for your plot size. The 6V tab-top rechargeable platform plus a solar panel port means the battery lasts the entire season without a mid-season swap.

Assembly is genuinely tool-free thanks to the Quick-Lock mounting system, and the six-foot fill height lets you pour corn from the bed of a truck without climbing. Real-world users report that the hopper holds just over 225 pounds of whole corn, slightly below the advertised 250-pound number, but the broadcast coverage remains consistent and the electronics have not shown the early failure pattern common in earlier Moultrie timer models.

The locking lid seals moisture out effectively, but the instructions bury the timer programming steps on a separate page — budget a few minutes of trial and error for your first schedule setup. The leg anchors and foot pads are strongly recommended because a fully loaded hopper can tip in high wind without them.

Check Price on Amazon

If you want corn on the ground without a single mechanical sound or battery to fail, the Moultrie Gravity Feeder delivers exactly that. The triple funnel feed system gives you three adjustable ports, each controlling its own flow rate so you can run corn in one, protein pellets in another, or restrict the opening to slow consumption. The entire unit operates on gravity alone — no timer, no motor, no spin plate — which means zero audible signature for deer to associate with human activity.

The 250-pound hopper is molded from heavy-duty UV-resistant polymer that has held up well under direct sun exposure in user reports stretching several months. Stainless steel fasteners and a reinforced tripod base with a 74-inch height keep the feed ports at an ideal elevation for mature bucks without forcing them to kneel. Assembly requires no tools, and the twist-on lid seals tightly enough that raccoons have trouble prying it open.

The biggest trade-off is the lack of scheduling control. You cannot time the feed release for pre-dawn hours, so deer learn to visit whenever they feel safe rather than at a predictable window. The adjustable ports also require some trial and error to set the flow rate slow enough to prevent corn from piling on the ground and spoiling.

Check Price on Amazon

The Boss Buck Gravity Feeder uses a roto-molded plastic barrel and galvanized hardware to keep corn dry through heavy rain and temperature swings. The 200-pound hopper sits on 75-inch galvanized tripod legs that elevate the feed ports high enough to discourage smaller mammals from climbing in while still being accessible to fawns. The three-way inner sleeve lets you adjust the flow from a trickle to a steady stream depending on the feed type, which is useful if you switch between corn and protein pellets mid-season.

User feedback highlights how quickly deer found this feeder — multiple reports of feeding activity on the first night. The 10-inch ports with a 10-degree overhang slow consumption naturally and reduce waste, and the 3-inch-deep lid hatch seals well enough to keep moisture out even during sustained downpours. The warranty service from Boss Buck has strong reviews, with one user reporting a replacement leg shipped promptly for a part they damaged during assembly.

A few buyers reported missing hardware — specifically the bolts to attach the inner feed cone and secure the lid. The bolts are 1/4-inch standard hardware, not metric, so a quick trip to the hardware store fixes the issue, but it is an annoyance for a unit at this price point. The 200-pound capacity is accurate for corn, but the hopper dimensions suggest it could handle slightly more if filled to the brim.

Check Price on Amazon

The Evolution feeder tackles the raccoon problem with a simple mechanical solution: the spinner plate is recessed underneath a heavy-duty mounting bracket and uses centrifugal force to drop down only during a feed cycle. A spring snaps it back flush against the container when the cycle ends, so critters have nothing to grab or climb into. The 40-gallon hopper holds up to 270 pounds of corn, and the timer supports up to six feed events per day with a fifty-foot distribution radius.

The powder-coated legs resist rust well, and the galvanized steel spinner plate does not warp or corrode after repeated wet cycles. The varmint-proof design earned strong praise from users who previously lost entire hoppers of corn to coons overnight. Assembly is straightforward, and the timer interface is intuitive enough to set up without the manual.

However, durability issues emerged in longer-term reviews. The plastic lid hinge can snap on the first fill if handled roughly, and the legs tend to slide apart when the feeder is dragged across the ground, which is common during positioning. One user reported the timer failing after three weeks of operation, though others have used the same unit for multiple seasons without issue. The build quality is inconsistent, which makes this unit best for budget-conscious setups where replacement cost is less painful than losing a premium feeder.

Check Price on Amazon

The Banks Outdoors Feed Bank mounts on a single 4×4 post rather than a tripod, which eliminates the risk of antler damage when bucks rub the feeder legs. The feed ports sit at 42 inches off the ground — optimal height to discourage raccoons and squirrels while still being reachable for does and young bucks. The 150-pound capacity is on the smaller side, but the weatherproof cover and large opening make filling fast and keep the contents dry.

Users consistently report excellent longevity. One reviewer noted their first Banks feeder lasted five years with only a silicone bead repair for a seam gap caused by UV deformation. The adjustable feed ports let you control the flow for corn or protein pellets, and the single-post design takes up less visual space in a food plot compared to a bulky tripod. Assembly is simple: slide the feeder onto a cemented 4×4 and tighten the retaining hardware.

The lid latches are the weakest point — multiple owners described them as lower quality than expected for the premium price tag. The plastic joint between the bin and base can deform over time under direct sun exposure, allowing water to seep in. A bead of exterior silicone at assembly time prevents this, but it is a modification you should plan for. The 150-pound capacity also means more frequent refills compared to 250-pound gravity feeders.

Check Price on Amazon

If you already own a feeder barrel and only need the control brain, The Timer by West Texas Feeders is the most reliable drop-in replacement on the market. It runs on either 6V or 12V power, works with the wiring kit included in the package, and has a battery backup that retains your settings during power loss. The illuminated buttons and display make programming easy even in low light, and the test function lets you verify the spin plate clears feed blockages without climbing the tripod.

User reports are remarkable: one review documented the timer firing twice daily for seven-second cycles over three full years before the screen started glitching. Other users replaced failed Moultrie timers with this unit and reported immediate reliability improvement. The glass-filled nylon case feels substantial, and the freestanding mount design gives you flexibility to install it inside a weatherproof box or directly on the hopper.

The warranty process received negative feedback from at least one user whose timer failed after 36 months — the manufacturer did not respond to two months of contact attempts, forcing a replacement purchase. The lack of a warranty certificate in the box was also noted. For most buyers, the three-year lifespan at this price point still beats cheaper timers that fail within one season.

Check Price on Amazon

The Foreverlast Road Feeder is the only unit in this guide built specifically for broadcasting corn from a moving ATV or truck. The 100-pound galvanized steel hopper mounts to a hitch or tailgate, and the 12V motor plugs directly into a cigarette lighter port with a long enough cord to reach the cab. A handheld on/off switch gives you instant control, so you can distribute corn along access roads, field edges, or trail intersections without leaving the vehicle.

The all-metal construction — American-made galvanized steel with no plastic components — means this unit will outlast any poly feeder in the same price tier. Users have repurposed it as a fertilizer spreader and seeder with minor modifications, which speaks to the motor power and spread pattern consistency. Assembly takes under fifteen minutes, and the included mounting hardware fits most standard hitches securely.

The 100-pound capacity limits use to short spreading sessions on smaller properties — you will need multiple trips for large food plots or extended road networks. The road-feeding approach also trains deer to associate vehicles with food, which can be counterproductive if you are trying to keep them pattern-able for hunting. This feeder excels as a supplementary broadcast tool rather than a primary feeding station.